75 lines
2.9 KiB
Markdown
75 lines
2.9 KiB
Markdown
# WiFiScanAsync Example
|
|
|
|
This example demonstrates how to use the WiFi library to scan available WiFi networks in asynchronous mode and print the results.
|
|
|
|
## Supported Targets
|
|
|
|
Currently this example supports the following targets.
|
|
|
|
| Supported Targets | ESP32 | ESP32-S2 | ESP32-C3 | ESP32-S3 | ESP32-C6 |
|
|
| ----------------- | ----- | -------- | -------- | -------- | -------- |
|
|
|
|
## How to Use Example
|
|
|
|
* How to install the Arduino IDE: [Install Arduino IDE](https://github.com/espressif/arduino-esp32/tree/master/docs/arduino-ide).
|
|
|
|
#### Using Arduino IDE
|
|
|
|
* Before Compile/Verify, select the correct board: `Tools -> Board`.
|
|
* Select the COM port: `Tools -> Port: xxx` where the `xxx` is the detected COM port.
|
|
|
|
#### Using Platform IO
|
|
|
|
* Select the COM port: `Devices` or setting the `upload_port` option on the `platformio.ini` file.
|
|
|
|
## Example/Log Output
|
|
|
|
```
|
|
Setup done
|
|
Scan start
|
|
Loop running...
|
|
Loop running...
|
|
Loop running...
|
|
Loop running...
|
|
Loop running...
|
|
Loop running...
|
|
Loop running...
|
|
Loop running...
|
|
Loop running...
|
|
|
|
Scan done
|
|
17 networks found
|
|
Nr | SSID | RSSI | CH | Encryption
|
|
1 | IoTNetwork | -62 | 1 | WPA2
|
|
2 | WiFiSSID | -62 | 1 | WPA2-EAP
|
|
3 | B3A7992 | -63 | 6 | WPA+WPA2
|
|
4 | WiFi | -63 | 6 | WPA3
|
|
5 | IoTNetwork2 | -64 | 11 | WPA2+WPA3
|
|
...
|
|
```
|
|
|
|
## Troubleshooting
|
|
|
|
***Important: Be sure you're using a good quality USB cable and you have enought power source for your project.***
|
|
|
|
* **Programming Fail:** If the programming/flash procedure fails, try to reduce the serial connection speed.
|
|
* **COM port not detected:** Check the USB cable connection and the USB to Serial driver installation.
|
|
|
|
If the error persist, you can ask help at the official [ESP32 forum](https://esp32.com) or see [Contribute](#contribute).
|
|
|
|
## Contribute
|
|
|
|
To know how to contribute to this project, see [How to contribute.](https://github.com/espressif/arduino-esp32/blob/master/CONTRIBUTING.rst)
|
|
|
|
If you have any **feedback** or **issue** to report on this example/library, please open an issue or fix it by creating a new PR. Contributions are more than welcome!
|
|
|
|
Before creating a new issue, be sure to try the Troubleshooting and to check if the same issue was already created by someone else.
|
|
|
|
## Resources
|
|
|
|
* Arduino-ESP32 Official Repository: [espressif/arduino-esp32](https://github.com/espressif/arduino-esp32)
|
|
* ESP32 Datasheet: [Link to datasheet](https://www.espressif.com/sites/default/files/documentation/esp32_datasheet_en.pdf)
|
|
* ESP32-S2 Datasheet: [Link to datasheet](https://www.espressif.com/sites/default/files/documentation/esp32-s2_datasheet_en.pdf)
|
|
* ESP32-C3 Datasheet: [Link to datasheet](https://www.espressif.com/sites/default/files/documentation/esp32-c3_datasheet_en.pdf)
|
|
* ESP32-C6 Datasheet: [Link to datasheet](https://www.espressif.com/sites/default/files/documentation/esp32-c6_datasheet_en.pdf)
|
|
* Official ESP-IDF documentation: [ESP-IDF](https://idf.espressif.com)
|